A POTA Win

Wednesday I finally succeeded with a solo POTA activation. I had tried a couple on my own before, but operator issues prevented me from logging a single contact each time.

I was better prepared for attempt #3. I had tested my antenna setup at home. I had spent time watching videos on the FT-891 to ensure I understood how its menus worked, so I could make necessary adjustments quickly. Using the FT-891 over the IC-705 was also a choice, offering me up to 100 watts rather than just 20.

How did it go? Read on…


It was another gorgeous day here in Indianapolis when I headed to Ft. Harrison State Park, US-2256. I arrived wearing a zipup hoodie but quickly ditched it. The temperature ranged from mid-60s to low-70s in the time I was in the park. Breezy and beautiful. Plenty of walkers and joggers enjoying the day, but I had a shelter to myself.

Using a 19 foot collapsible pole, I got one end of my Chameleon 60 foot end-fed antenna up into the air, the transformer tied off to the shelter roof support.

A quick scan of the bands revealed plenty of activity and the POTA.app page looked busy. I grabbed one park-to-park as a hunter to make sure my signal was getting out, then spotted myself and started calling CQ. An immediate response, a 59 from my home state of Kansas. Great start!

Then I called CQ for 10 minutes without anyone else responding.

I checked every setting I could think of. 100 watts of SSB power. SWR below 1.5. Antenna connections were tight. Everything checked out.

I decided to bail on the calling and started hunting. Over the next hour I added nine more contacts to push my total to 11. Frustrating that I wasn’t hunted more, but unlike my first two attempts this one was official!

Next, I wanted to test the very cool Greyline FT8 app. It allows you to run FT-8 on an iPad or iPhone when connected via a USB cable to your rig. I purchased it about a month ago, seeing it as a way to support my IC-705 activations. If 20 watts isn’t enough to get 10 contacts on a given day, switch to FT8 and finish up there.

However, after I purchased it I discovered the while app would key the transmitter, it would not actually send any RF out. I began corresponding with Jon, the app’s terrific developer. He had me try several things and eventually determined the 705 needs a different cord connection than the basic, Amazon cables he suggested on his website. He’s currently working with Digirig to get that cable made.

Not being the patient sort, I ordered a Digirig DR-891 to use with my FT-891. While I figured 100 watts (or even 50-75) should be enough to complete an activation on phone, it would be nice to add more via FT8 when I had enough of talking to people.

I tested this new setup at home and was successful. It worked in the park as well. I added six more contacts in about 30 minutes of work. My goal was 10, but I had several fail to complete. I don’t think those failures were the fault of the app.

Based on my QSO map, it looks like I was getting out in all directions, but I was hoping for a lot more. The gentleman who activated the same park the previous day logged 70 contacts. Perhaps a better antenna setup next time will lead to more success for me. After I was done I found a nice spot on the opposite side of the park with some large trees that would allow me to get my antenna quite a bit higher. Even better, they are right next to parking spots and out of the main foot traffic area, so I could activate from there in cold weather, from the warmth of my car.

My only other complaint was the World Radio League logger. Perhaps it was because I didn’t have the strongest of cell signals, but it seemed very laggy. A couple times when I hit enter to log a contact, it would spin for several moments. Once I had to refresh the page and re-add the previous contact. Had I been taking calls from hunters, this would not have been a nightmare. In my previous co-activations, I had used Ham2K Polo with zero problems. I think I will go back to that for my next activation.